XS Power PSC30 30A Intellisupply – 12/14/16V

$399.99

The XS Power PSC30 Intellisupply is a 30A power supply / Intellicharger designed to be in-vehicle mounted.  This ideal for RVs or any vehicle with a battery or battery bank which needs charged often with minimal hassle.

The PSC30 includes a Remote LCD display / remote control which can be mounted in the dash to manage operation.  Battery connections are via a 6ft 10 AWG pigtail pre-terminated with a 50A Breakaway connector (mating half is included).  Compatible with 12V, 14V and 16V flooded, maintenance free, deep cycle, gel-cell, and AGM (Absorbed Glass Mat)batteries.

Full specifications provided below.

Description

The IntelliSUPPLY is an advanced power supply unit and battery charger designed specifically for high  performance lead-acid batteries. This power supply/charger uses MOSFET rectifier technology with an advanced microprocessor control board to create a battery charger and power supply that can rapidly and safely recharge  12V, 14V and 16V flooded, maintenance free, deep cycle, gel-cell, and AGM (Absorbed Glass Mat) batteries  in several sizes. The wireless remote and digital display makes the IntelliSUPPLY very easy to use.

Multi-Stage Charging

At the heart of the technology in the XS Power IntelliSUPPLY are the three distinct charging stages and DC  power output. During the first stage, called “Bulk” charging, the charger will regulate the current the voltage is  allowed to float. During this stage, 80% of the battery’s capacity is restored.

When the battery’s cell voltage comes up to the correct level, the second stage called “Absorption” charging is engaged.  During this stage the voltage is fixed according to the battery type and voltage switches on the front panel and the current  is allowed to float. The battery is brought to 100% during this stage and the cells are equalized.

The third stage is float charging. During this stage the voltage and current are reduced to a level that will maintain  the battery indefinitely.

Several microprocessors are used to tightly control the entire process. This is the same technique that battery manufacturers recommend and use in the production of new batteries and it is the fastest and safest technique for battery charging.

Compatible With All Lead-Acid Type Batteries

Lead-acid batteries have different charging requirements based on their specific design. Flooded and maintenance free batteries require a higher voltage per cell than do sealed valve regulated types such as AGM and gel cell  batteries. Overcharging will reduce the life of any battery as sealed valve regulated batteries are especially sensitive to high charging voltages and overcharging. Some sealed valve regulated batteries are more sensitive to overcharging than others. If in doubt as to which battery setting to use for your application, contact the manufacturer of the battery being charged. Overcharging an AGM or gel-cell battery will cause permanent damage.

Power Supply Mode

Along with charging batteries, the XS Power PSC Chargers can operate as a Power Supply. When this mode is selected, the Charger will maintain a constant output voltage and current. Power Supply mode can be used for audio display boards, as a test bench power supply, etc. Power Supply Mode should not be used to charge AGM Batteries.

Desulfation Mode

At the end of a battery’s life, or in the event that a battery has sat uncharged for an elongated amount of time, It can become sulfated. This would reduce the capacity and performance of the battery. The PSC Chargers have the ability to recondition a battery that has sulfated. Through a complex charging cycle and microprocessor controlled pulsed output, the PSC charger can break down the sulfated crystals inside the battery which cause the lack in performance. Using this mode on older batteries once every few months is advisable to prolong battery life.

Remote Control/ Display

A remotely mounted display will show the status of the charging functions of the PSC models. This feature allows the user to control power on/off. The remote displays important charger and battery information such as  voltage, charge rate, mode, fault, and status of the battery being charged.

Voltage Monitoring

The battery’s terminal voltage is measured every five minutes by the on-board microprocessors and this information is analyzed in addition to the elapsed time to dynamically control the Battery Charger for optimum charging performance.

Automatic Computer Analysis/Auto Shutdown

The microprocessors will analyze the battery when connected. If the battery’s voltage is below 4V or the battery will  not come up to the correct voltage in a ten-hour period the charger will automatically shut off.

UL Approved Battery Cables

Six feet of durable battery cables are provided that are resistant to cuts and abrasion. The copper plated battery clamps are compact and custom designed easy connections. All clamp connections are soldered for maximum current flow.

Internal Cooling Fan

A cooling fan automatically operates during charging to keep the transformer and other internal components at a constant safe temperature.

Specifications

Input Voltage:  120VAC (90~130VAC) via IEC connector
Frequency Range:  45~65Hz
Efficiency:  >=85%
Power Factor:  0.5 at full load (+/-5%)
Output Voltage:  12V / 14V / 16V Selectable with a maximum of 2.4V per cell
Output Current:  30A Continuous / Maximum
Output Connections:  6ft 10 AWG leads with 50A Breakaway Connector (mating half included)
Remote Display Cord:  20ft long flat cord with RJ45 connectors on each end
Remote Display Mounting:  Mounting bracket included

Dimensions:  9.9″ x 5.6″ x 2.85″ (252mm x 142mm x 72mm)
Weight:  5.5lbs (2.5kgs)

Reviews

There are no reviews yet.


Be the first to review “XS Power PSC30 30A Intellisupply – 12/14/16V”

No more offers for this product!